Wiki

# Current network setup for IPv6 router VM on local virtualbox setup
# /etc/sysconfig/network-scripts/ifcfg-enp0s3
# Network interface enp0s3 is IPv4 for public internet access
TYPE="Ethernet"
BOOTPROTO="dhcp"
DEFROUTE="yes"
PEERDNS="yes"
PEERROUTES="yes"
IPV4_FAILURE_FATAL="no"
IPV6INIT="yes"
IPV6_AUTOCONF="yes"
IPV6_DEFROUTE="yes"
IPV6_PEERDNS="yes"
IPV6_PEERROUTES="yes"
IPV6_FAILURE_FATAL="no"
NAME="enp0s3"
UUID="32bad876-680a-4f78-a364-726eae21bfcf"
DEVICE="enp0s3"
ONBOOT="yes"

# /etc/sysconfig/network-scripts/ifcfg-enp0s8
# Network interface enp0s8 is IPv6 internal interface to provide IPv6 to internal hosts
BOOTPROTO=static
IPV6INIT=yes
IPV6ADDR="2001:db8:0:2::1/64"
NAME=enp0s8
UUID=e931a806-2f76-425d-b035-d37813b81df5
DEVICE=enp0s8
ONBOOT=yes
NM_CONTROLLED=no

# Disable NetworkManager
systemctl disable NetworkManager

# Install dhcp.x86_64, dhcp-common.x86_64, radvd.x86_64 if not already installed
yum install dhcp-common
yum install dhcp
yum install radvd

# /etc/sysctl.conf Set sysctl to enable IPv6 forwarding
net.ipv6.conf.all.forwarding=1
net.ipv6.conf.enp0s3.accept_ra=2
net.ipv6.conf.enp0s3.accept_ra_defrtr=1
net.ipv6.conf.enp0s3.router_solicitations=1

# /etc/radvd.conf
interface enp0s8
{
# This is the primary "on switch" for RADVD

  AdvSendAdvert on;     

#
# These settings determine how often advertisements will be sent every X-Y.
# X and Y are in seconds. With these settings you will be sending a advert every 60 seconds
#

  MinRtrAdvInterval 60;
  MaxRtrAdvInterval 180;

#
# Disable Mobile IPv6 support
#

  AdvHomeAgentFlag off;

# Here we set our managed flags

  AdvManagedFlag on;
  AdvOtherConfigFlag on;

#
# Enter our IPv6 prefix and CIDR
#

  prefix 2001:db8:0:2::/64
  {
      AdvOnLink on;
      ### On link tells the host that the default router is on the same "link" as it is
      AdvAutonomous on;
      AdvRouterAddr off;
  };

};

# Enable radvd service
systemctl enable radvd

# In /etc/sysconfig/network add
IPV6FORWARDING=yes

# Current network setup for IPv6 router VM on local virtualbox setup
# /etc/sysconfig/network-scripts/ifcfg-enp0s3
# Network interface enp0s3 is IPv4 for public internet access
TYPE="Ethernet"
BOOTPROTO="dhcp"
DEFROUTE="yes"
PEERDNS="yes"
PEERROUTES="yes"
IPV4_FAILURE_FATAL="no"
IPV6INIT="yes"
IPV6_AUTOCONF="yes"
IPV6_DEFROUTE="yes"
IPV6_PEERDNS="yes"
IPV6_PEERROUTES="yes"
IPV6_FAILURE_FATAL="no"
NAME="enp0s3"
UUID="32bad876-680a-4f78-a364-726eae21bfcf"
DEVICE="enp0s3"
ONBOOT="yes"

# /etc/sysconfig/network-scripts/ifcfg-enp0s8
# Network interface enp0s8 is IPv6 internal interface to provide IPv6 to internal hosts
BOOTPROTO=static
IPV6INIT=yes
IPV6ADDR="2001:db8:0:2::1/64"
NAME=enp0s8
UUID=e931a806-2f76-425d-b035-d37813b81df5
DEVICE=enp0s8
ONBOOT=yes
NM_CONTROLLED=no

# Disable NetworkManager
systemctl disable NetworkManager

# Install dhcp.x86_64, dhcp-common.x86_64, radvd.x86_64 if not already installed
yum install dhcp-common
yum install dhcp
yum install radvd

# /etc/sysctl.conf Set sysctl to enable IPv6 forwarding
net.ipv6.conf.all.forwarding=1
net.ipv6.conf.enp0s3.accept_ra=2
net.ipv6.conf.enp0s3.accept_ra_defrtr=1
net.ipv6.conf.enp0s3.router_solicitations=1

# /etc/dhcp/dhcpd6.conf
# DHCP for IPv6 Server Configuration file.

# Enable RFC 5007 support (same than for DHCPv4)

  allow leasequery;

# IPv6 address valid lifetime
# (at the end the address is no longer usable by the client)
# (set to 30 days, the usual IPv6 default)

  default-lease-time 2592000;

# IPv6 address preferred lifetime
# (at the end the address is deprecated, i.e., the client should use
# other addresses for new connections)
# (set to 7 days, the usual IPv6 default)

  preferred-lifetime 604800;

# T1, the delay before Renew
# (default is 1/2 preferred lifetime)
# (set to 1 hour)

  option dhcp-renewal-time 3600;

# T2, the delay before Rebind (if Renews failed)
# (default is 3/4 preferred lifetime)
# (set to 2 hours)

  option dhcp-rebinding-time 7200;

# The path of the lease file

  dhcpv6-lease-file-name "/var/lib/dhcpd/dhcpd6.leases";

# Set preference to 255 (maximum) in order to avoid waiting for
# additional servers when there is only one

  option dhcp6.preference 255;

# Server side command to enable rapid-commit (2 packet exchange)

  option dhcp6.rapid-commit;

# The delay before information-request refresh
# (minimum is 10 minutes, maximum one day, default is to not refresh)
# (set to 6 hours)

  option dhcp6.info-refresh-time 21600;

# Set this to `interim' when doing ddns updates

  ddns-update-style interim;

  subnet6 2001:db8:0:2::/64 {
      option dhcp6.name-servers 2001:db8:0:2::1;
      option dhcp6.domain-search "opnfv.local";
      ddns-hostname = concat(binary-to-ascii(10, 8, "-", leased-address), ".wired");
      ddns-domainname = "opnfv.local";
      # Our address range 1000 through 1fff
      range6 2001:db8:0:2::1000 2001:db8:0:2::1fff;
  }

# In /etc/sysconfig/network add
IPV6FORWARDING=yes

For reference "How to set up RADVd DHCPv6 and DNS on CentOS 6" refer http://www.percula.info/archives/196